Crown Audio by Harman

Search:     Advanced search
Glossary



How do I mike a group discusson for recording and PA?

I want to capture the conversation of a group of people sitting in an oval circle on the floor and joining some question/answer kind of discussions. The oval circle will have people sitting 3 ft to 10 ft from a central location where I suppose the mic could be positioned on a carpeted floor.  

Ideally I would like to feed the mic to an amplifier system which connects to a set of speakers installed at different locations (same floor and other floors). If this is not possible, I would like to record the conversation for playing back at a later time. What kind of mic I could use? How should I organize the system? Dr. Rabin Raut, Videotron  

Reply: A PZM would be ideal for this situation as long as its amplified audio is not sent to speakers that are near the microphone . I'd recommend a PZM-30D on the floor in the center of the circle of people. This microphone requires phantom power , which is supplied by the mixer that you plug it into. If your mixer does not have phantom power , connect the PZM to a phantom power supply such as the Crown PH-1A. The PH-1A is powered by the Crown PS-24 AC-DC adapter. Connect the output of the PH-1A to the mic input of your mixer. (See the figure below).  

  

I'll call the group of people sitting on the floor the "local group". If there are loudspeakers near the local group, you need a way to send the PZM signal only to distant groups or participants. And you need a way to turn off the PZM when people in the local group are listening to questions fed to loudspeakers near them. In other words, you don't want the PZM to pick up the loudspeakers near the local group because this would cause echoes or feedback.  

One way around this problem is to give each person in the local group an inexpensive earphone to listen to instead of loudspeakers. The earphone can be a low-cost "earbud" type of headphone which you can find in Target, K-Mart, Wall-Mart, Radio Shack, etc. You can use headphone extension cables where needed.  

The figure above shows a suggested system. Connect the PZM and all distant microphones to the mixer, and connect the mixer to a stereo amplifier. (You might use a combined mixer/amplifier). Channel 1 of the amplifier drives an earphone box which has several headphone jacks all wired to the same cable from the amplifier. Ideally, this earphone box is driven off a headphone jack in the mixer, or is connected to amplifier channel 1 through a 100-ohm resistor . Channel 2 of the amplifier drives loudspeakers or earphones that are near the distant microphones. Each distant mic is placed very close each person speaking in order to avoid picking up the loudspeakers.  

Another method: If you need broadcast-quality audio from the local group, give each person a clip-on lavalier microphone, such as a Crown GLM-100. Feed the mics into an automatic gated mixer, and from there to an amplifier and loudspeakers. With this system, you probably will not need to use earphones. 

Others in this Category
document How do I control Blackberry or cellphone interference in MB microphones?
document How do I combine two mics into one input?
document How should I mike a video shoot?
document Which Crown mic works with a sound card?
document Do you have a surface-mounted (boundary) mic with an on-off switch?
document Can you recommend a sweat-resistant tape for face mics (headworn mics)?
document How should I mike our congregation with PZMs?
document How should I mike a wedding? (1 of 3)
document How should I mike a wedding (2 of 3)
document How should I mike a wedding? (3 of 3)
document How can I pick up ambient stage sound for in-ear monitors?
document Where do I order replacement parts for my Crown headset?
document How can I mike an observation room with a PZM-10?
document Why is it important to use a matched mic pair for stereo recording?
document How can I make a Mid-Side (MS) stereo mic with PZM and PCC mics?
document What mic would you recommend for voiceover and acoustic guitar?
document Where should I place a PZM-11LL to prevent pickup of duct noise?
document What mic should I use for recording a therapy session?
document What mics are good for a video shoot?
document What is a good spy mic to record conversations?
document How can I mike a group discussion for broadcast?
document How do I record students in a classroom?
document How can I prevent feedback with my lectern microphone?
document Is there a replacement for the Crown PS-24 power supply?
document Do you have a wall-mountable or wireless microphone for voice recognition or handicapped use?
document How can I record dialog and ambience for video?
document Please explain mixer connections, equalizers, compressors, and groups.
document I can't hear my monitor speaker.
document How should I use phantom power?
document How do I purchase Crown products?
document How do I return a microphone for factory service?
document How can I make a line-level to mic-level adapter for my camcorder?
document How to mike a tap dancer?
document How to mike a roomful of computer operators?
document Siren indicator for deaf drivers
document Water-resistant microphones
document How to record direct? Please explain impedances and levels.
document Help choosing a headset microphone
document Picking up birds at a nature center
document PZM mounting and waterproofing
document Miking a classical music ensemble
document How do I prevent breath pops with the CM-311A?
document Can the PZM-11LLWR be changed from its line-level output to a mic-level output?
document How to mike students and eliminate background noise?
document Which Crown microphone has a connector that fits a mini digital camcorder?
document Where can I get Crown mic parts and service?
document Clandestine listening room
document I need a mixer for a 3-mic PA system
document Please recommend a paging mic for the Crown 180MA mixer-amp.