PIP and IQ-PIP Modules

PIP^TM (Programmable Input Processor) Modules open up a completely new realm of capability for CTs and Macro-Tech amplifiers.* Simply plugged into the rear-mounted PIP connector of these amplifiers, they provide a cost-effective, convenient alternative to outboard processors or inferior systems that can compromise performance. A wide, ever-expanding assortment of PIP modules are available.

* Click here for amplifier/module compatibility info

P.I.P.-CLP is designed to detect and prevent overload. The same error detecting circuit that is used to signal the IOC indicator is used to activate this error-driven compressor. It is not a typical signal-driven compressor, but a circuit to prevent any overload. It can yield up to 13 dB or additional signal safety margin without noticeable program change.
P.I.P.-CLP page

PIP-Lite is a PIP input module for PIP2-compatible amplifiers. It connects the amplifier to a 100 Mb Ethernet network allowing it to be remotely controlled and monitored via IQ. It can be connected to the same network used to pass CobraNet audio. The PIP-Lite implements SmartAmp features: input compressors, multimode output limiters, error reporting and load monitoring.

Requires FREE IQwic Software and a computer for initial setup.

* You must have a PIP2-compatible amplifier to use the PIP-Lite. To determine if your amplifier is PIP2-compatible, look for the PIP2 logo on the back of the amplifier.
PIP-Lite page

PIP-USP3 is a 3rd generation DSP-based PIP (Programmable Input Processor) input module for PIP2 compatible amplifiers.* It connects the amplifier to a 100 Mb Ethernet network allowing it to be remotely controlled and monitored via IQ. The USP3 is a TCP/IQ series component and connects to the audio control/monitor network using standard 100Mb Ethernet hardware (switches, Network Interface Cards, and cables). The USP3s SHARC DSP processor gives the user an enormous amount of digital signal processing. Audio routing, faders, meters, polarity & mute, input compressors, filters, delays, multimode output limiters, error reporting, and load monitoring are all available. A built in noise generator and sine-wave generator provide noise masking and test capabilities. The enhanced AUX port capability allows the user to interface with the amplifier to provide external manual control and monitoring. Offering crisp, clear sound and the wide dynamic range possible with full 24-bit converters, the PIP-USP3 provides unprecedented power and flexibility in one compactand very affordablemodule.

Requires FREE IQwic Software and a computer for initial setup.

* You must have a PIP2-compatible amplifier to use the PIP-USP3. To determine if your amplifier is PIP2-compatible, look for the PIP2 logo on the back of the amplifier.
PIP-USP3 page

PIP-USP3CN is a 3rd-generation DSP-based PIP (Programmable Input Processor) input module for PIP2 compatible amplifiers.* It connects the amplifier to a 100 Mb Ethernet network allowing it to be remotely controlled and monitored via IQ. In addition, the USP3/CN allows the transport of real-time digital audio via CobraNet over the same Ethernet network. The USP3/CN is a TCP/IQ series component and connects to the audio control/monitor network using a standard 100Mb Ethernet hardware (switches, Network Interface Cards, and cables). CobraNet audio is available over the same 100Mb Ethernet network, providing a simple to install, single plug solution for audio distribution, control, and monitoring. The USP3/CNs SHARC DSP processor gives the user an enormous amount of digital signal processing. Audio routing, faders, meters, polarity & mute, input compressors, filters, delays, multimode output limiters, error reporting, and load monitoring are all available. A built in noise generator and sine-wave generator provide noise masking and test capabilities. The enhanced AUX port capability allows the user to interface with the amplifier to provide external manual control and monitoring. Offering crisp, clear sound and the wide dynamic range possible with CobraNet, the PIP-USP3/CN provides unprecedented power and flexibility in one compactand very affordablemodule.

Requires FREE IQwic Software and a computer for initial setup.

* You must have a PIP2-compatible amplifier to use the PIP-USP3. To determine if your amplifier is PIP2-compatible, look for the PIP2 logo on the back of the amplifier.
PIP-USP3CN page